Honeywell Micro Dome 2.0MP Network IR 20m. Len 2.8mm. WDR Built-in mic
Honeywell DVR 16CH CVBS/AHD 2 SATA 2.0MP
Honeywell DVR 8CH CVBS/AHD 1 SATA 2.0MP
Honeywell DVR 4CH CVBS/AHD 1 SATA 2.0MP
Honeywell Bullet Camera 2.0MP CVBS/CVI/TVI/AHD IR 40m. Len 2.8-12mm.
Honeywell Eyeball Camera 2.0MP CVBS/CVI/TVI/AHD IR 30m. Len 2.8-12mm.
Honeywell Bullet Camera 2.0MP CVBS/CVI/TVI/AHD IR 20m. Len 3.6mm.
Honeywell Eyeball Camera 2.0MP CVBS/CVI/TVI/AHD IR 20m. Len 3.6mm.
FDM-1 is a standard-sized dual monitor module used to monitor and supervise two independent two-wire Style B (Class B) dry-contact initiating device circuits (IDCs) at two separate, consecutive addres
FZM-1 is a standard-sized module used to monitor and supervise compatible two-wire, 24 volt, smoke detectors on a Class A (Style D) or Class B (Style B) circuit.
FMM-101 is a miniature monitor module (a mere 1.3" (3.302 cm) H x 2.75" (6.985 cm) W x 0.5" (1.270 cm) D) used to supervise a Class B (Style B) circuit of dry-contact input devices.
FRM-1 Addressable Relay Module provides the system with a dry-contact output for activating a variety of auxiliary devices, such as fans, dampers, control equipment, etc.
FZM-1 is a standard-sized module used to monitor and supervise compatible two-wire, 24 volt, smoke detectors on a Class A (Style D) or Class B (Style B) circuit.
The FRM-1 Relay Control Module is intended for use in intelligent, two-wire systems where the individual address of each module is selected using the built-in rotary switches.
The NOTIFIER ISO-X Fault Isolator Module is used with the NFS-3030, AM2020, AFP1010, NFS-640, AFP-400, AFP-300, AFP-200, AFP-100 and System 5000 (equipped with an AIM-200 module) to protect the system
FMM-1 is a standard-sized module (typically mounts to a 4" [10.16 cm] square box) that supervises either a Class A (Style D) or Class B (Style B) circuit of dry-contact input devices.
FCM-1 Addressable Control Module provides Notifier intelligent control panels a circuit for Notification Appliances (horns, strobes, speakers) or to monitor a telephone circuit.
Notifier 851 Series intelligent plug-in smoke detectors with integral communication provide features that surpass conventional detectors.
The FSM500K provides both signaling of an alarm to the Fire Indicator Panel and local LED indication of activation.
Notifier FST-851 Series intelligent plug-in smoke detectors with integral communication provide features that surpass conventional detectors.
Notifier 851 Series intelligent plug-in smoke detectors with integral communication provide features that surpass conventional detectors.
The Thermotech 302 Series rate-anticipation heat detectors operate within a controlled range of two to three degrees of their set points, regardless of the speed or rate of temperature rise.
The 5151 thermal detector meets the needs for applications where rapid response is vital and rapid temperature increases would only be caused by a fire emergency.
System Sensor’s 5600 Series mechanical heat detectors offer a low-cost option for property protection against fire and for non-life-safety installations, where smoke detectors are inappropriate.
System Sensor’s 800 series detectors are 2-wire conventional profile plug-in detectors aimed to meet the performance criteria designated by UL.
The SD-651 is designed to meet the performance criteria designated by UL. Its sensing chambers are sealed against back pressure air flow, dirt, and insects.
The System Sensor BEAM1224S is transmitter / receiver unit and a reflector as fourwire conventional projected beam smoke detectors.
The InnovairFlex™ Series are the only duct smoke detectors flexible enough to fit configurations from square to rectangular and everything in between.
The System Sensor BEAM1224 is transmitter / receiver unit and a reflector as fourwire conventional projected beam smoke detectors.
System Sensor 100 Series Plug-in Smoke Detectors offer superb performance and reliability in a profile which is just 2˝ (5.1 cm) deep.
The 2151 low-profile photoelectronic detector uses a state-of-the-art optical sensing chamber. This detector is designed to provide open area protection and to be used with compatible UL listed contro
System Sensor i3™ sounder and relay smoke detectors apply the guiding principles of installation ease, intelligence, and instant inspection in a series of specialty conventional devices.
System Sensor’s 800 series detectors are 2-wire conventional profile plug-in detectors aimed to meet the performance criteria designated by UL.
System Sensor selectable output horns, strobes, and horn strobes are rich with features guaranteed to reduce installation times and maximize profits.
System Sensor® SP2 and SP3 Series speakers combine performance, functionality, and flexibility in the latest line of dualvoltage evacuation speakers.
System Sensor’s SSM Series alarm bells are low-current, high-decibel notification appliances for use in fire and burglary systems or other signaling applications.
System Sensor® SpectrAlert® Advance selectable-output horns, strobes and horn/strobes are rich with features guaranteed to cut installation times and maximize profits.
System Sensor® SpectrAlert® Advance selectable-output horns, strobes and horn/strobes are rich with features guaranteed to cut installation times and maximize profits.
The SpectrAlert Advance series offers the most versatile and easy-to-use line of low frequency sounder and low frequency sounder strobes in the industry.
The SpectrAlert Advance series offers the most versatile and easy-to-use line of low frequency sounder and low frequency sounder strobes in the industry.